What does a P0442 code mean?
Can you safely drive with an active P0442 code?
Read on to learn all you need to know about OBD code P0442.
This Article Contains:
- What Is P0442?
- Common Symptoms
- P0442 Code Causes
- Can I Still Drive?
- Diagnosis
- Possible Repairs for P0442 & Costs
What Is P0442?
Engine code P0442 stands for “Evaporative Emission Control System Leak Detected (Small Leak).” It’s a diagnostic trouble code indicating problems with the Evaporative Emission Control (EVAP) System.
The EVAP system consists of the fuel tank, a charcoal canister, valves (vent valve and EVAP purge valve), hoses, and a sealed fuel tank gas cap. It prevents fuel vapor from escaping into the atmosphere via the fuel tank or fuel system and directs it to the engine to burn off.
The Electronic Control Module (ECM) regularly runs a leak test within the EVAP system using the fuel tank pressure sensor. It creates a vacuum in the system with intake manifold suction. If a leak occurs, the vacuum pressure will drop more quickly than expected. The ECM interprets it as a potential issue and triggers the P0442 code.
Common Symptoms
The P0442 code usually doesn’t manifest itself in noticeable signs. That said, it does exhibit a few common EVAP code symptoms that you could look out for, like:
1. An Illuminated Check Engine Light
It’s almost impossible to physically detect an EVAP leak. So when the leak detection pump in the exhaust system suspects a small EVAP leak event, it immediately turns the Check Engine Light on.
While the engine light doesn’t necessarily indicate the P0442 code, getting your car checked is a good idea.
2. Poor Gas Mileage Due to the EVAP Leak
Refilling at the gas station too often?
If the EVAP vent solenoid and EVAP purge solenoid can’t control the opening of their respective valves, it could lead to an EVAP leak and a drop in fuel economy.
Here’s how:
The EVAP canister stores the gas vapors so the engine can use them during combustion. When these valves don’t function, the vapors escape, leading to a lean air-fuel mix. This causes the ECM to overcompensate by injecting more fuel into the system, decreasing gas mileage.
You may also notice a fuel smell from the engine due to the leaking gas vapors.
3. A Failed Emissions Test or Smoke Test
One of the main indicators of the P0442 code is a failed emission test or a smoke test.
A smoke test uses a smoke machine to find hard-to-detect fuel vapor leaks. The smoke machine adds pressure and smoke to the fuel system, making small leaks visible.
P0442 Code Causes
Various EVAP system factors can trigger the P0442 code.
Some common reasons why you’re seeing this engine code include:
- A loose or bad fuel cap
- Using an incorrect fuel filler cap or filler tube
- A broken fuel filler neck
- Damaged fuel pump
- EVAP system line leak
- Charcoal canister leak
- Fuel tank leak
- Fuel line leak
- Faulty fuel tank pressure (FTP) sensor
- Damaged or leaking fuel vapor hose or hose clamp
- Malfunctioning vent valve or purge valve (leaking internally)
- Faulty or damaged EVAP vent solenoid or purge solenoid
- Failed leak detection pump
Can I Still Drive?
Code P0442 is generally a mild code in terms of its impact on vehicle drivability and safety — it doesn’t show any adverse symptoms.
That said, an EVAP system leak may release fuel vapors into the atmosphere, which is rather dangerous. So, it’s best to contact a mechanic if your vehicle fails an emissions test.
Diagnosis
Since the P0442 code indicates an Evaporative Emission System leak, it needs careful diagnosis and resolution. A small leak in the EVAP system can harm the environment and the car owner, so it’s recommended that you seek help rather than attempting any DIY troubleshooting.
Keeping that in mind, here’s how your mechanic would diagnose the P0442 code:
- When detecting an EVAP error code, the first thing they’ll do is connect the OBD-II scan tool to the engine and check which codes show up.
- They’ll start by inspecting the gas cap. A damaged or loose gas cap or an incorrectly placed fuel filler cap can trigger the P0442 code.
- Once the fuel cap is tightened or replaced with a new gas cap, your mechanic will clear all codes to check if they show up again. If they do, additional diagnosis is needed.
- Your mechanic will check for a cracked or disconnected EVAP hose near the engine air box.
- They’ll inspect the fuel tank and charcoal canister for damage and leaks and check the purge volume control valve and purge solenoid for proper operation.
- They’ll examine the charcoal canister vent control valve to make sure it’s working properly.
- If everything else works fine, the EVAP leak may be too small to diagnose physically. In that case, they’ll run a smoke test to detect the small EVAP leak.
Possible Repairs for P0442 & Costs
Since many potential issues can cause an Evaporative Emission System leak, you can resolve the P0442 code through a combination of various repairs. These include:
- Tightening a loose gas cap
- Installing a new gas cap
- Cleaning the gas tank and gas cap
- Replacing the EVAP canister purge valve
- Replacing the EVAP purge solenoid
- Replacing the EVAP vent valve or its solenoid
- Replacing the charcoal canister or the EVAP line (rare)
EVAP code repair costs range anywhere from $50-$600 (excluding labor), depending on the severity of the issue and the repairs required. To that, you can add about $75-$150 in labor charges.
Here are the estimated costs of different EVAP parts:
- Hose clamp: $5
- Charcoal canister vent control valve: $20-$50
- Gas cap: $20-$60
- Fuel line: $50-$150
- New fuel filler neck: $60 and $700
- EVAP purge valve: $15 to $500
- Charcoal canister: $200-$400
Get Expert Help with Your P0442 Code
AutoNation Mobile Service is here to keep you moving. Our experienced mobile technicians can quickly diagnose a P0442 trouble code and are available 7 days a week. Pick a time that works best for you, and our expert mechanics will bring the shop to you.
Get a quick and fair quote today.